5 thoughts on “Crystal jewelry hand decoration shooting method”
Inez
The method is as follows:
1. Set the flashes of the main light We set the main light flash on the leg leg with a soft hood. Then add the battery box and wireless motion device. In we set the light from the top of the subject, and the light is hit from top to bottom.
In the main light is set up, some fine -tuning the ring, and at the same time use the exposure table to check the exposure index. The table shows 1/60 @ f/8.0, we set the camera according to this setting. After that, we set the camera position through the mobile tripod, set the best angle of the lens to move the gimbal, and finally took the first photo. This results show that we need to move the main light forward so that some lights are hit in front of the ring.
Is to adjust the main light and restart the ring.
It to check the light with the exposure table to get the same index and start the second shooting.
3-4 inches of moving lights The results of the shooting show the light feeling above the ring. Metal feels good, with clear highlights and good outlines. Now we need to do some work on stone, because we hope to see the carving surface of the stone, making the color of sapphire look more fresh. 2. Use the spotlight We use some spotlights to brighten the stone, increase the gloss, and look more fresh. It the lighting system we choose, Dedo150W concentrated tungsten lamp. We used three sets of lamps and color paper. We lamps on the left position of 90 degrees of camera and concentrate on the ring. To correct the color of the lights, we add blue filter on the filter paper clip of the Dedo lamp head. We look at the lighting effect from the viewfinder, and our assistant helps us to fine -tune the light. At the same time, adjust the position of the ring to make the stones on both sides more. It looks good, we started new shooting.
The results show that the details of the stone have been greatly improved, and some gloss can be seen on the right side of the ring. The small props we choose now also show its texture. In order to increase the same effect on the left side of the ring, we put the second Dedo spotlight on the right. The difference is that we put this dedo lamp on the DL bracket so that we put the light closer. Is when I look at the viewfinder, our assistant made the last adjustment of the light. We then started shooting again.
Now we are very close to the photos worth looking forward to. The increase in the second light is the tips on the right side of the ring. Finally, we reflect part of the light to the subject with a 12 -inch LITEDISC, and the metal luster in front of the ring was brightened further. is the time when we shoot the most beautiful films.
If you want two cups, you have to be above the oblique. Don't use the surrounding metering, replace it with a center or point test. The first one is confused, it is not sharp enough, so don't hold it or automatically focus, it is easy to be confused.
The method is as follows:
1. Set the flashes of the main light
We set the main light flash on the leg leg with a soft hood. Then add the battery box and wireless motion device.
In we set the light from the top of the subject, and the light is hit from top to bottom.
In the main light is set up, some fine -tuning the ring, and at the same time use the exposure table to check the exposure index. The table shows 1/60 @ f/8.0, we set the camera according to this setting. After that, we set the camera position through the mobile tripod, set the best angle of the lens to move the gimbal, and finally took the first photo.
This results show that we need to move the main light forward so that some lights are hit in front of the ring.
Is to adjust the main light and restart the ring.
It to check the light with the exposure table to get the same index and start the second shooting.
3-4 inches of moving lights
The results of the shooting show the light feeling above the ring. Metal feels good, with clear highlights and good outlines. Now we need to do some work on stone, because we hope to see the carving surface of the stone, making the color of sapphire look more fresh.
2. Use the spotlight
We use some spotlights to brighten the stone, increase the gloss, and look more fresh.
It the lighting system we choose, Dedo150W concentrated tungsten lamp. We used three sets of lamps and color paper.
We lamps on the left position of 90 degrees of camera and concentrate on the ring. To correct the color of the lights, we add blue filter on the filter paper clip of the Dedo lamp head.
We look at the lighting effect from the viewfinder, and our assistant helps us to fine -tune the light. At the same time, adjust the position of the ring to make the stones on both sides more. It looks good, we started new shooting.
The results show that the details of the stone have been greatly improved, and some gloss can be seen on the right side of the ring. The small props we choose now also show its texture.
In order to increase the same effect on the left side of the ring, we put the second Dedo spotlight on the right. The difference is that we put this dedo lamp on the DL bracket so that we put the light closer.
Is when I look at the viewfinder, our assistant made the last adjustment of the light. We then started shooting again.
Now we are very close to the photos worth looking forward to. The increase in the second light is the tips on the right side of the ring. Finally, we reflect part of the light to the subject with a 12 -inch LITEDISC, and the metal luster in front of the ring was brightened further.
is the time when we shoot the most beautiful films.
If you want two cups, you have to be above the oblique. Don't use the surrounding metering, replace it with a center or point test. The first one is confused, it is not sharp enough, so don't hold it or automatically focus, it is easy to be confused.
Three lamps are needed, and the top is also needed.
You are using the two soft light boxes that you use. People use a soft light box and a hard light to hit Lunburst light. Can you say the same?
Dear, can't shoot. These two skewers are not one thing. Take me, dear.