3 thoughts on “The problem”

  1. What is a ghost lamp?
    This lamp is a new type of headlights containing pheasant, also known as high -strength discharge gas lamp, and English for short in English. High -voltage inert gas -Xenon's radon, replacing traditional filaments, has mercury and carbonic compounds on the two sections of electrodes. Through the stabilizer with 23,000 volt high -voltage current stimulates the gasposum, forming a perfect white arc between the bipolar, the emitted light is close to Very perfect sunlight.

    The lighting principle of the lamp (HID)
    This HID pyrine lamps are different from traditional halogen lamps. This is a high -voltage discharge lamp. Rare metal chemical reactions are glowing, so there is a small glass ball in the lamp, which is filled with sorbe and a little rare metal. As long as the current is used to stimulate them for chemical reactions, the two will emit up to 4000K-12000K color color. The light of temperature. It uses a special ballast that uses a car battery 12V voltage to generate a trigger voltage above 23000V to start the lights. The brightness of 0.8 seconds at startup is 20% of the rated brightness, reaching the brightness of the halogen lights, and reaching the headlights to more than 80% of the rated brightness within 4 seconds. After the lamp is stable, the ballast provides about 80V power supply voltage to keep the lights run at a constant power. The performance advantages of the lamp (HID) (HID) 1, the general 55W halogen lamp can only produce 1,000 lumen light, while the 35W pyrine can produce 3,200 lumen strong light, which increases the brightness of 300%. It has a wide and wide -angle wide view. Bring you unprecedented driving comfort; make the night no longer dark, and the vision is clearer, which can greatly reduce the driving accident rate. 2. The HID pillar lamp is used to stimulate the gase of gases in electronic, and there is no tungsten wire. Therefore, the life span is long, about 3,000 hours, which greatly exceeds the total number of time of driving at night at night. The halogen lamp is only 250 hours. 3. Strong power saving: The pyrine lamp is only 35W, and the light of 55W halogen lamps emits more than 3.5 times, which greatly reduces the load of the automotive power system. The power loss saves 40%, which improves the performance of the vehicle accordingly and saves energy. 4. Good color temperature: 4300K-12000K, etc., 6000K is close to the sunlight, which is well received by the majority of users. The halogen lamp is only 3000K, and the light color is dim and red. 5, constant output, safe and reliable: When the power supply system and battery of the car fail, the ballast is automatically closed and stopped working. (The lumens of the lamp and the halogen lamp, the color mild life comparison table) The development status of the global ghost lamp (HID) has been published in BMW in Germany in 1991 ("HID" English full name: High Intensity Discharge Chinese Translation: High -intensity Gas discharge lamp), the earliest Mercedes -Benz E -Class car in 1995 has begun to apply HID pyrine lights to the present, and more than 20 million cars in the world have installed mounted lamps. It has been popular in Europe and the United States and Southeast Asia for six years. It is known as the Revolutionary Car Lighting Product of the 21st Century. It is believed that it will become the necessary assembly for cars after the ABS brake system and airbags (Airbag) in the future ... … HID's ghost lamp increases the brightness of the original car halogen lamp, the color is better, the color temperature penetration is stronger, the light is farther, and the performance is more stable. It is favored by more and more car modification users around the world. At present, the demand for HID pyrine lamps in Europe is growing at a rate of 13 % per year. HID boring headlights are generally installed in Japanese and high -end cars in Japan. The Audi A6 and Passat 2.8v6, Sonata 2.7, etc. were installed with HID pyrine lamps. It is expected that in the next two or three or three years, the models of domestic vehicles equipped with gel lamps will increase greatly. Experts predict that by 2008, the proportion of new European cars with HID lamps will reach 21% (4.8 million vehicles), and Japan will be as high as 40% (3.8 million vehicles). The replacement of halogen lamps in the lanterns of the gel cars will become a new trend in the 21st century. However, because of the control cost, it is still a very few high -end cars to choose a car mackerel headlight in the original car. There are only a handful of automotive carrier lamp manufacturers in the world. They have always been represented by German Haraka, Panasonic, Japan and South Korea. The brands that are generally recognized in Europe are: Hella, Philips, OSRAM, KDG. These four major products have stable performance and pure color, while domestic bleaching light manufacturers are represented by Guangdong, China (actually assembled and processed). The price is low and the quality is difficult to guarantee. The relevant technical patents are monopolized by several well -known companies in the world, such as Hyela, Panasonic in Japan, and KDG in South Korea. With the close connection between OEM and ODM between global companies, the production of high -pressure packages of pyrine lamps is basically based on the above three houses mentioned above. Control, for example, in Asia, those well -known brands of sturgeon lamps are basically produced in KDG OEM. The KDG factory has seven related patents related to gas lamp technology, and has taken a considerable advantage in the technology and production capacity of the airlight lamp. At present, the many domestic sturgeon lamp products on the market are actually made by different dealers as required. The price is about 1,000 yuan. In 2005, there were many domestic branded air lamps in Shenzhen to grab the market. However, in 2006, in the Shenzhen market, Basically, there is no domestic brand's storing lights, mainly because the quality of the product is not closed. In the market, the price of the double -gallium lamp of Piaa in Japan is more than 10,000 yuan, and the price of Philips single lights cost more than 5,000 yuan. The price is so high, resulting in some low -end car owners. This is the result of brand effects and some merchants' hype.

    —————————————————————————————————————————————————————————————————— ——————————————————

    HID is the abbreviation of High Intensity Discharge, that is, high -pressure gas discharge lamp, the principle of glowing is 12V 12V The voltage voltage to the ultra -high voltage of 23000V, which is scrubbed to be filled with the mirror of the quartz tube, making it glow. Then turn the voltage to about 85V, and stable and continuously supply the gel light bubbles.
    The color temperature of the sun in the day is 5000K, and the HID light is closer to the white light of the sun. In addition, HID also avoids the problem of general halogen lights that are easy to oxidize and the longer light, and the darker the light is, and the lighting distance is wide and long.
    1, brightness, using the same wattage HID, the brightness is about 2 to 3 times of tungsten wire lamp. Although the glowing arc of the ghost lamp is similar to the length of the tungsten wire of the halogen lamp, the lighting efficiency and the brightness of the light have been increased by nearly 3 times.
    2, energy saving, compared with tungsten silk lamps, can save nearly half of the power. Equipment such as air conditioners and GPS vehicles requires power consumption, while car lighting headlights are one of the largest drills consumption. The advantage of saving half of the power is obvious.
    3, long life, because there is no filament, without the defects of traditional lamps that are easy to break, the life of HID has also increased by nearly 10 times, which can be used up to 2000 ~ 3000 hours.
    4, security, in fact, this is the greatest charm of HID. Many owners who have used HID responded, and the HID lights were installed well, and the safety of driving at night was greatly improved. This is mainly because the multiple beams and intensity brought by HID lights will be more effective than simple and near -light settings. It can greatly improve the lighting in front of the car and illuminate the signs of the roadside. Suspicious.
    5, is urgent. Due to the different principles of glowing and halogen lamps, when the battery power supply has a problem, it will extend a few seconds to allow the owner to deal with the emergency situation. R N Most of the fake air lamps are used to increase the voltage of the halogen lamp and generate high brightness to cheat consumers. So, how to know the eye lights and distinguish the true and false air lamps? The use of false air lamps is generally: first, the temperature is high, some are due to high temperature scratch lamps, as well as burning -soluble lamps. Secondly, the effect is poor, compared with HID, not enough light, poor color. Moreover, its power consumption is large, and it is necessary to use an enhanced line. Therefore, this needs to open the eyes during the purchase process, and the cost performance is poor. Because of the large consumption, the idle speed is high, and the fuel consumption is too much. Some need to replace the import spark plug in order to ensure the power supply system. Therefore, this needs to open your eyes during the purchase process, and select the quality of the quality of the quality. In this way, you can also achieve the effect of superiority.

    —————————————————————————————————————————————— ————————

    HID, the full name is the gas discharge light, the principle is like the lightning of nature. Some are inert gases such as xenon and iodide, and then instantly supercharged the DC voltage of the 12 volts on the car through the Ballast to the current of the DC voltage of the 12 volts to 23,000 volts. Electronic free, generates light sources between the two electrodes, is the so -called gas discharge. When you watch the bulbs carefully, you will find that there is a spherical glass ball in the middle. By the way, the inside is a sorbent, and the yellow one is rare metal! When the transformer is given a high pressure of 23000V, the pyroph who is penetrated, and the sorbe after being divided will emit unimaginable light. The color temperature can be as high as 5000K-8000K, but the light of the sun at noon is only 5500K. You can imagine how bright it is!
    This lamp, also known as the radio light, activates it with a high brightness light under the action of radio diode and high -voltage current. The color temperature of ordinary halogen lamps is around 2000-2500K, while the color temperature of the pyrine lamps is generally above 5000K to 8000K, which is close to blue and white, so it looks dazzling, the effect is clearer, and the characteristics of light concentration, not easy to astigmatism, and decaying attenuation , So it looks very bright.
    1. Output of three times brightness:

    Mepatinating a maximum of 1000LM degrees, while HID is 3200LM degrees. For those who are often driving at night, the safety factor is greatly improved The fatigue degree also decreased greatly!

    2. Life assurance of ten times:

    If you are a car family, you may encounter the halogen lights on the car suddenly not bright, the result is tungsten filament burning The case, indeed, because the luminous principle of halogen lamps is caused by tungsten filament, and tungsten wires are difficult to keep damaging at high heat; Too high temperature, so as long as the sorchium is not used up, it can glow normally, and it is not easy to damage! According to a study, even if the high -quality halogen bulbs, the life expectancy is 400 hours, and the general HID has the least life span. 3,000 hours, even in normal car, HID can be used for 6-7 years!

    —————————————————————————————————————————————— ————————

    HID is the English abbreviation of High Intensity Discharge high -pressure gas discharge lamp, which can be called heavy metal lights or pyrine lamps. Its principle is in the UV-CUT anti-ultraviolet crystal quartz glass tube. Most of the chemical gases are filled, most of which are inert gases such as xenon and iodide, and then the car is used through the Ballast. The DC voltage of the 12 volts instantly supercharged to a current of 23,000 volts. After the high voltage shock amplitude, the pyrone electronics in the quartz tube are excited, and the light sources are generated between the two electrodes. This is the so -called gas discharge. The white ultra -strong arc light generated by the gas can increase the temperature value of the light, similar to the sunlight of the day. The current volume required for HID is only 3.5A. The brightness is three times the traditional halogen bulbs. Halogen bulbs 10 times long.

    The English name of 氙 gas discharge lamp is High Intensity Discharge, which is abbreviated as H.I.D. Essence There is a small glass ball in the lamp in the H.I.D bulb, which fills the gas gas and a little rare metal mercury. When the current and ultra -high voltage are used, the pyrine and the metal mercury have a fierce chemical reaction to release the light close to the noon sun. It is a traditional car halogen tungsten lamp 5 times brightness.
    The traditional car halogen tungsten filament car lights start with a voltage of 12 volts, but it is absolutely not enough to stimulate the gas glowing. The truly full set of HID gas discharge lights (as shown below) requires a voltage stabilizer (Ballast), which increases the voltage of the vehicle 12V to 23000V. The ultra -high voltage that burst into an instant , The voltage dropped to 85V, stabilized and continuously supplying the gel light bubbles.

    HID is the abbreviation of the lamp, also known as the high -strength discharge gas lamp. Fill the high -voltage grid in the quartz lamps to replace the traditional filament. There are mercury and carbonic compounds on the two sections of electrodes. It is 23,000 volt high -voltage current to stimulate the gel. The white arc is formed between the poles. The light emitted is very close to the sunlight. The car HID pyrine lamp is different from the traditional halogen lamp. This is a high -voltage discharge lamp. Its light emitting principle is to use positive and negative electrical stimulation to stimulate the radon with rare metal chemical reactions. Therefore, there is a small glass ball in the lamp. Among them It is filled with a few rare metals. As long as the current is used to stimulate them for chemical reactions, the two will emit light with a light of 4000K-12000K color temperature. It uses a special ballast that uses a car battery 12V voltage to generate a trigger voltage above 23000V to start the lights. The brightness of 0.8 seconds at startup is 20% of the rated brightness, reaching the brightness of the halogen lights, and reaching the headlights to more than 80% of the rated brightness within 4 seconds. After the lamp is stable, the ballast provides about 80V power supply voltage to keep the lights run at a constant power. HID has nearly 300%higher than the general halogen lamp. The service life is longer. The color is close to the sunlight, but the price is higher.

    HID What is it? : HID is the English abbreviation of High Intensity Discharge high -voltage gas discharge lamp, which can be called heavy metal lights or pyrine lamps. Its principle is in the UV-CUT anti-ultraviolet crystal quartz glass tube. Most of the chemical gases are filled, most of which are inert gases such as xenon and iodide, and then the car is used through the Ballast. The DC voltage of the 12 volts instantly supercharged to a current of 23,000 volts. After the high voltage shock amplitude, the pyrone electronics in the quartz tube are excited, and the light sources are generated between the two electrodes. This is the so -called gas discharge. The white ultra -strong arc light generated by the gas can increase the temperature value of the light, similar to the sunlight of the day. The current volume required for HID is only 3.5A. The brightness is three times the traditional halogen bulbs. Halogen bulbs 10 times long.

    This lamp, also known as high -strength gas discharge lamp, in English referred to as HID. The carbon lamp products are composed of pyrum bulbs, transformer stabilizers and insulating wires. The working principle is that after the power is connected, through the transformer, the 12V power supply is raised to a high-voltage pulse voltage of more than 20,000 volts in an instant to activate the strong light of 6000K --10000K in the arc in the arc. The color is slightly purple blue in the white diamond. It completely abandoned the traditional principle of burning tungsten filament and is a revolutionary change in the field of lighting systems.
    The principle of using special gaseous gas to distribute electricity under the ultra -high voltage state.
    1 The color system is wide, from 4000 to 10,000 distribution, pure light color.
    2 is small in power, only 35W, 60%of power saving, but the light and distance are more than 3 times the conventional headlights. Bai Guang has doubled your body price. It is also the basic configuration of the world's top models.
    HID superiority:
    ● The color temperature of the ghost lamp is similar to the sunlight, but it contains more green and blue Ingredients, therefore appear blue and white. This blue and white light greatly increases the brightness of road signs and signs.
    ● HID is three times the brightness efficiency of the halogen lights, which has obvious effects on improving the clearness of driving sight at night and fog.
    ● The light flux emitted by the lamp is more than 2 times the halogen lamp. At the same time, the efficiency of the transformation of electrical energy to light energy is also more than 70%than the halogen lamp. Half of the halogen lamp. The improvement of the brightness of the car lights also effectively expands the visual range in front of the car, thereby creating a safer driving conditions.
    ● Power saving 1/2, halogen lamps consume less than 60W of electricity, and the pyrine lamp is only 35W electricity.
    ● Since the lamps are not filaments, the problem of scrapped by filaments is not scrapped. The service life is much longer than the halogen lamp.
    ● Once the lamp fails, it will not go out instantly. Instead, it will go out in a darker way, so that the driver can win the time in the night driving and park it urgently.
    ● The lamp will not produce excess glare, and will not cause interference to the driver who comes to the car.

    —————————————————————————————————————————————— ————————

    H.I.D's full English name is Hight Intensity Discharge, which has now become the target of many bulb manufacturers. The earliest use of the new Mercedes -Benz E -Class car that was used in 1995. From then on, the gas discharge headlight H.I.D had replaced the ordinary carnivorous headlights to become a new configuration standard for high -end cars, and the modification industry was even more expensive. The cars with H.I.D with H.I.D are watched with H.I.D lights.

    . Different from traditional bulbs, the H.I.D bulb has no filament. It relies on the gas medium in the high voltage to break through the gas medium in the light to generate a bright high -colored warm light. In addition, the 35W power consumption (only half of the ordinary light bulb) also reduces the burden on the car battery. In addition, H.I.D's excellent lighting ability provides a wider field of vision for the driver at night, and the gloss of the recent light also greatly reduces the degree of eyes fatigue during the night car. Of course, the dazzling effect has also become the focus of passers -by.

    Although there are such advantages, the main reason why H.I.D is currently unable to promote in the market is that the price is high, not ordinary people can bear it, because in addition to the particularity of H.I.D, it also has its important one. "High voltage" problem. When H.I.D starts, a voltage of 23,000 volts is required. Once the voltage is reduced to about 85 volts, such a high working voltage is arranged on a car that is frequent, high -temperature, high and humid, and even traffic accidents at any time. Therefore, "personal safety" It is an important issue for becoming a lamp manufacturer. When H.I.D must occur when the bulb rupture, wire falling off, and abnormal voltage occur, the perceived circuit in the stabilizer can immediately cut off high voltage to protect the safety of the person in the vehicle. In addition, the voltage of the battery 12 volt is doubled by a 23,000 volt transformer, the high insulating wire and the design of the anti -electromagnetic interference, etc., all causes the high cost of H.I.D.
    This lamps have the following features:
    1, high color temperature, light color blue. It looks handsome. The K number is the sign of the K number, and the general halogen lamp color temperature is below 3000. The lamp is generally starting at 4500K. 7000K is ordinary. Two days ago, I saw a buddy saying that there were 12000K lanterns, and it was crazy. The high number of K is generally easier to accept in recent days, but I think the real benefit of high color temperature is just good -looking, and other effects are not great.
    2, high brightness, note that the gentleness of the color is the fundamental concept of differentness. The light light is not because the color temperature is high, but because of the high brightness. The units of brightness are lumens, and the number of lumens of the lamp is generally three times that of ordinary halogen lamps.
    3, other elephant consumption is small, and long life has little to do with us.

    Gas discharge light source. The halogen lights emit light through the burning light. The gas discharge lamp shines through the arc generated between the poles. As a result, brighter and higher life span. What the gas discharge light is not only needed in another bubble. It requires a trigger to generate a 25KV startup voltage and and the ballast to control the entire system.
    Gas discharge itself is not a new thing. The requirements for the light source used in the car are quite harsh, and a breakthrough in gas discharge technology must be made to create a miniature compact discharge tube controlled by precision electronic devices.
    This results are surprising; use high -tech electronic equipment to generate instantaneous light -pass light sources, higher light output, reduce energy consumption, and use a reflector with better light control functions. Brightness. The benefits of drivers are also surprising: a wider field of vision range and a better light distribution on the road. The life expectancy of the car exclude the possibility of replacing the light source. The light color is close to the sunlight. All these have improved significantly for safety improvement and comfort driving. In addition, auto manufacturers also benefit from smaller front lights, lower temperatures allowed to use plastic, and reduced energy consumption.
    : Lights: The revolution of automobile lighting
    The current and future market trends are higher requirements for lighting equipment. This also occurs on the front lights and other lighting equipment. The development trend of front lights is to be more secure on the basis of better visual effects and economy costs, and has a long life and shape design of aerodynamics. The market requires economy, long life, high -light and anti -vibration products. As a guaranteed lighting system supplier, Philips has improved gas discharge light sources and electronic control devices. Now it has proposed a revolutionary solution for automotive lighting: 氙 lamps.
    xenon is a lighting system that contains three mutually matching parts. A miniature gas discharge lamp is used as a light source, an electronic device controls the start and burn point, and the fine matching front lighting fixture ensures the best lighting effect. The quality of lighting is doubled, and the energy consumption of half of the halogen lamp is used. Its life span has been prolonged by 5 times, emitting the light color close to the sun and allowing the highly compact front lighting design. In the end, it is not the most important thing. It can start directly after it goes off.

    —————————————————————————————————————————————— —————————

    This lamp is successfully developed by Philips for 5 years. The original pyrine lamp is still through the original halogen bulbs to add more activity to a stronger pheasant. In success, nowadays have developed to high -voltage discharge of light -free wireless lights, and the lamps of the pyretellar vehicle have three times the brightness compared with the average lamp, exuding light -like light, and the projection range is far and wide. It saves 45 % higher than the average halogen lamp, and the life span is 5 times longer than the halogen lamp, reaching 3,000 hours. At present, the demand for sturgeon lamps in Europe is growing at a rate of 13 % per year. It is also installed in Japanese and high -end cars in Japan and high -end cars, and this kind of lamps in Hong Kong are more popular. Only the Audi A6 and Passat 2.8 are installed in domestic cars. Therefore, if other domestic car owners want to upgrade the lights, they have to buy modified pyrine lamps to install.

  2. 1 — The cold state startup time of the storing loading light only takes 1.5 ~ 2.5 seconds to enter the normal working state. So how long does it take to enter the normal ignition state when it is turned off after a period of time turning off the lights after a period of time turning off the lights and then turning on immediately after turning on the lights.

    2 -s the service life of HID bulbs? It is related to those factors, and how much is the relationship?
    0. Manufacturer (who is the best quality?)
    1. Order time (Can you reach the nominal?)
    2. n3. Voltage fluctuations at the time of use (constantly changing at 10.0V ~ 15.0V)
    4. Vibration
    5. Use temperature (whether it is normal at about 100 degrees)
    6.ballast manufacturing quality r r
    7. Installation orientation (except for horizontal use, stand upside down, does it affect the ignition of upward and downward?

    3 —— when the HID light bulb and the balast model do not match the model, what will happen? ?
    1. Don't light up (under what circumstances?)
    2. Boil light bulbs (under what circumstances?)
    3. Is there a life limit for a flower (Ballast)? (In that case, it will be burned)

    4 -What will happen when the life of the HID is ends?
    1. The brightness becomes lower
    2 It is difficult to start
    3. Light color changes
    4. The power consumption is large

    5 —— how much is the market price of the HID ballast? Beijing)

    6 -I want to know more technical details about HID ballasts

Leave a Comment